小間距LED顯示屏
主要技術指標(品牌︰金曉,型號︰JX-KXB,可定制)︰
小間距LED顯示屏
l 像素間距(mm)︰≦1.25;
l LED配置︰每個象素由紅、綠、藍三基色LED組成;
l 箱體平整度(mm)︰≦0.2;
l 光學參數︰單點單點亮度校正和單點顏色校正;
l 白平衡亮度︰≧600cd/m2 (色溫6500K,校正後);
l 燈珠封裝方式︰COB封裝;
l 優選國際主流品牌燈珠並提供原廠授權證明;
l 色溫︰不低于3500~6500K內範圍可調;
l 像素失控率不超過1 ;
l 水平視角︰≧175°;
l 垂直視角︰≧175°;
l 發光點中心距偏差︰<3%;
l 亮度均勻性︰≧97%;
l 箱體材料︰一體化壓鑄鋁,後面板非塑料材質;
l 模塊帶有CPU及存儲器,校正數據儲存在模塊內,並在模塊內通過CPU進行均勻性的智能處理。確保模塊可以快速簡單地進行更換;
l 色度均勻性︰±0.003Cx,Cy之內;
l 最大對比度︰5000:1;
l 亮度調節︰可根據環境照度的變化對顯示屏亮度進行自動調整;
l 信號畫面延時︰經過拼接控制器處理的畫面與不處理的畫面對比測試,延時不超過100ms;
l 信號切換︰任何輸入信號之前的信號切換必須是立即切換,不能出現黑屏、卡頓、三方過渡切換等現象,信號切換小于100ms;
l 圖像預監︰支持所有輸入信號同時在一個屏幕上預監;
l 平均功率︰≦250W/m2;峰值功耗︰≦600W/m2;
l 驅動方式︰恆流驅動;
l 供電要求︰為更好的適應市電波動,LED顯示單元需采用寬壓電源,電源波動在100~240V之間,設備可正常工作;
l 換幀頻率(Hz)︰50&60;
l 平均壽命︰≧10萬小時;
l 整體產品的MTBF︰≧1萬小時;
l 熱插拔︰為保證大屏整體維護的便捷性,要求投標產品具有完全前維護及模組熱插拔功能;
l 無線纜設計︰為保證大屏的美觀性,LED箱體內部采用硬連接方式,背部采用無線纜設計,可貼牆安裝;
l 模組和箱體散熱設計︰為保證大屏具有良好的散熱性,LED顯示單元箱體電源與機箱之間具有導熱 脂,LED模組背板具有敷銅設計;
l 低亮高灰功能︰LED屏要求在20%~100%亮度區間內,均具備16bit灰度;
l 校正技術︰為方便後期大屏維護,設備需支持逐點校正參數存儲;
l 防潮處理︰為達到更好的防潮效果,延長大屏使用壽命,LED燈板模組需具備納米鍍膜;
l 防藍光︰為保證LED藍光輻射能量值不會對人眼產生傷害,LED產品光輻射性能符合IEC/TR62778-2014標準;
l 防護等級︰為達到更好的防護性能,箱體後面板防護等級不低于IP66;
l 防輻射︰為保證LED顯示屏輻射不會對人體造成傷害,投標產品其輻騷擾值需要符合GB/T9254-2008 中Class B要求;
LED控制器
l 含LED顯示屏控制器或圖像發送卡;
l 要求支持不少于1路DVI輸入和輸出接口、1路HDMI輸入和輸出接口、1路音頻輸入和輸出接口、不少于2路管理網口;
l 輸出分辨率︰≧1920×1080,支持1080P,1024×768、1366×768等;
l LED顯示屏控制器支持設備級聯,可批量搜索及修改設備IP,支持遠距離配置設備IP及業務;
l 含PLC電控櫃,支持PLC遠程智能控制系統,可執行遠程設定、控制及開關機操作,具備過壓、過流、欠壓、短路、斷路及漏電保護措施,支持手動和遠程的一鍵啟動、一鍵停止和單點點動控制;
l 系統線纜︰包括圖像控制器至LED顯示單元的DVI線纜、控制網線、網絡線纜等;
l 含小間距LED顯示單元之間控制需要的以太網交換機等必要的輔助材料及設施等;